Depending on the roof structure and planning constraints, a loft conversion is one of the most straightforward ways of getting extra space. Almost all houses can benefit from this extension with a bit of basic planning
Yes – all loft conversions need Buildings Regulation approval, regardless of whether planning permission is needed or not. A building control surveyor will inspect your work at various stages and will issue you with a completion certificate on final inspection.
If your home is semi-detached or terraced, you’ll need to notify your neighbour of your proposals if the works fall under the Party Wall Act requirements. For instance, if you are building in beams which will bear on the party wall(s).
Loft Conversion Assessment
The features that will decide the suitability of the roof space for a loft conversion are the available head height, the pitch and the type of structure, as well as any obstacles such as water tanks or chimney stacks. An inspection of the roof space will reveal its structure and physical dimensions.
Take a measurement from the bottom of the ridge timber to the top of the ceiling joist; the useable part of the roof should be greater than 2.2m.
If you have appointed an architect or designer, invite them to illustrate clearly how much headroom there will be across the floor in the finished space. Some people are disappointed by how much standing space they actually have, and this isn’t always conveyed on plans.
The Building Regulations impose no minimum ceiling height for habitable rooms. The headroom standard for stairs of 2m applies, but this can be relaxed to 1.9m or 1.8m on the edge of a stair if necessary.
Without the roof space for water tanks and plumbing, the heating and hot water system may have to be replaced with a sealed system. Unvented hot water cylinders make a better choice than replacing the boiler with a combi (combination) boiler but they do take up a cupboard-sized room, which you will have to find space and budget for.
The higher the pitch angle, the higher the central head height is likely to be, and if dormers are used or the roof is redesigned, the floor area can be increased.
Type of Roof Structure
Two main structures are used for roof construction — namely traditional framed type and truss section type. The traditional framed type is typically found in pre-1960s houses where the rafters and ceiling joists, together with supporting timbers, are cut to size on site and assembled. This type of structure has more structural input, so is often the most suitable type for attic conversions. The space can be easily, and relatively inexpensively, opened up by strengthening the rafters and adding supports as specified by a structural engineer.
Post 1960s, the most popular form of construction used factory-made roof trusses. These utilise thinner – and therefore cheaper timbers – but have structural integrity by the addition of braced diagonal timbers. They allow a house roof to be erected and felted in a day. However, this type of truss suggests that there are no loadbearing structures beneath, and so opening up the space requires a greater added structural input.
This will normally involve the insertion of steel beams between loadbearing walls for the new floor joists to hang on and the rafter section to be supported on — together with a steel beam at the ridge. This added structural input requires skill, knowledge and equipment that would limit scope as far as DIY is concerned — and a far greater cash outlay. It is advisable to seek advice from specialist firms in this instance.
How can I Convert my Loft With a Low Head Height?
If the initial roof space inspection reveals a head height of less than 2.2m, there are two available – but costly – solutions that will require professional input.
Solution 1: Raise the Roof
This would involve removing part or whole of the existing roof, and rebuilding it to give the required height and structure. This is structurally feasible, but the major problems are the high cost and getting planning permission approval. If the whole roof area needs removing, a covered scaffold structure, to protect the house from the weather during the works, would also be required.
Solution 2: Lower the Ceiling in the Room Below
The ceiling height in some rooms in older properties may be 3m or more, so if the roof space height is limited there is the option of lowering the ceilings below, providing it still allows at least 2.4m. This will require all the existing ceilings in question to be removed, causing much mess. With this method a plate will need to be bolted to the wall using shield anchors or rawlbolts, for the new floor joists to hang from. There is also a need for a suitable tie between the roof structure and the dwarf wall formed, to prevent the roof spreading. Any DIY involvement will be limited to supervised demolition and clearing up.
New Ceiling Joists
The existing ceiling joists are unlikely to be adequate to take a conversion floor, so additional new joists will be required to comply with the Building Regulations. The size and grade would have been specified by the structural engineer, who will have taken into account the span and the separation distance for a given loading.
The new joists span between load-bearing walls, and are normally raised slightly above the existing ceiling plasterwork by using spacers below the joist ends. This spacing must be sufficient to prevent any new floor joist deflection from touching the ceiling plaster below. The new joists run alongside the existing joists. Above window and door openings, thicker timbers are used to bridge the opening, so that pressure is not put on the existing opening lintel.
Rolled steel joists (known as RSJs) are also specified to distribute the load, and in some installations are used to carry the ends of the new joists. If head height is limited, then thicker joists, more closely spaced, can be specified.
Your Building Control inspector will specify exactly what you require. The roof structure can be insulated in one of two main ways:
Cold Roof Loft Insulation
The most straightforward is to use a ‘cold roof’ method. This involves filling the space between the rafters with 70mm-thick slab foam insulation such as Celotex, ensuring that there is 50mm spacing between the roofing felt and the insulation (for ventilation via the roof and soffit vents).
In addition, 30mm slab insulation is attached to the inside of the rafters, giving a total of 100mm of insulation. The rafter thickness is often less than 120mm, so a batten may be required along each rafter to allow the 50mm spacing and the 70mm insulation. The roof section requires 300mm of mineral wool insulation (e.g. Rockwool), or 150mm of slab foam insulation, such as Celotex. This method can be undertaken by the DIYer.
Warm Roof Loft Insulation
The other main method is ‘warm roof’. This method uses 100mm Celotex insulation or similar over the rafters, and a covering capping, followed by the tile battens and tiles. This is not really a practical option unless the roof coverings have been stripped off. It could be used with a dormer, especially if it has a flat roof.
Continuity of insulation between walls and roof is required to avoid any cold bridging. The dormer walls can be insulated with 100mm Celotex between the studwork. The internal partition walls use a 100mm quilt that will provide sound insulation. Plasterboard is attached to one side of the wall then the quilt inserted, followed by plasterboard on the other side. Insulation is also placed between floor joists, and this is typically 100mm-thick Rockwool fibre or similar — mainly for its sound-reduction properties.
Insulating the Floor
Insulating the floor can be achieved by a mineral fibre quilt laid between the joists. Use the heavier, denser sound insulation quilt.
Insulating Party Walls
If you live in a terraced or semi-detached home, it is often necessary to insulate the party walls — both against heat loss and noise. Introducing timber studwork with mineral fibre insulation will allow you to achieve both and it can be covered with sound-rated
Staircase to Your Loft Extension
The ideal location for a staircase to land is in line with the roof ridge: this will make best use of the available height above the staircase.
The minimum height requirement above the pitch line is 2m, although this could be reduced to 1.9m in the centre, and 1.8m to the side of a stair. In practice, the actual position will depend upon the layout of the floor below, and where necessary the available height can be achieved using a dormer or adding a rooflight above the staircase or, if appropriate, converting a hip roof end to a gable.
Maximum Number of Steps: The Building Regulations specify that the maximum number of steps in a straight line is 16. This is not normally a problem, as a typical installation usually only requires 13 steps.
Step Size: The maximum step rise is 220mm, whereas the step depth or ‘going’ is a minimum of 220mm; these measurements are taken from the pitch point. The step normally has a nose that projects 16-20mm in front of the pitch line. However, the ratio of size must not exceed the maximum angle of pitch requirement of 42°. Any winders must have a minimum of 50mm at the narrowest point. The width of steps is unregulated, but in practice the winders are likely to limit the reduction in width.
Balustrading: The height minimum is 900mm above the pitch line, and any spindles must have a separation distance that a 100mm sphere cannot pass through.
Bespoke Staircase Solutions
Sometimes a bespoke solution is required. Bespoke staircases cost much more than standard off-the-shelf models, so it pays to consider all your options. It is also worth having the design approved by your Building Control body to ensure the staircase will comply. Ask your joiner or builder to email a copy for approval before the staircase is fabricated.
Windows and Dormer Windows for Loft Conversions
The loft room will require a means of getting natural light and ventilation.
Rooflights for Loft conversions
Typically this does not involve much structural alteration. The most straightforward method is to use rooflights that follow the pitch line of the roof. This type is fitted by removing the tiles and battens where the rooflight will be fitted. The rafters are cut to make way for the rooflight after suitably reinforcing the remaining rafters.The rooflight frame is then fitted and flashings added before making good the surrounding tiling.
This type of window is the most economic, and more likely to be allowed without planning permission, under your Permitted Development rights. Conservation rooflights, which are slightly more flush to the roofline and are made of metal, can also be specified.
Dormers not only give natural light but can add space to a loft extension; they can be at the ends or sides. They are particularly effective where the pitch angle is high, as the useful floor area can be increased. The mansard type will give maximum conversion roof space because it projects the maximum available head height, thus giving a greater usable floor area. A hip to gable conversion has a similar effect.
Dormers and other similar conversions are normally installed by opening up the roof, and cutting the required specified timbers to size on site. They normally involve compound angle cuts so may not be a task that a DIYer would like to undertake. Care also needs to be taken with the roof and side coverings, to get a good weatherproof structure.
Some loft conversion companies will make the dormers off site in their workshop and lift into place. This process allows quick installation, and quick weatherproofing.
Dormers can have gabled or hip roofs, and with careful design can enhance a roof line. In practice, a mixture of the available types can result in the maximum light and space, and provide a fire exit.
Loft Conversion Fire Safety
Ensure that the new windows are large enough and low enough to escape from:
Things become more complicated if your loft conversion transforms a two-storey house into a three-storey home:
The new floor joists of your loft conversion will need to offer at least 30 minutes’ worth of fire protection, which could mean replastering the ceilings in those first floor rooms below. The loft room will also have to be separated by a fire door, either at the top or bottom of the new stairs.
The existing doors on the stairway to both ground and first floor should be able to provide 20 minutes of fire resistance or be replaced. They can’t be glazed either (unless with fire-rated glass), so you may want to consider windows or rooflights to bring daylight to the stairwell.
Mains-powered smoke alarms should be installed on each floor of your home and interlinked so that they all sound off when one is activated. Most have a rechargeable battery as a back up that allows the supply to be extended from a lighting circuit if necessary. Wireless, radio-linked alarms can be fitted if you can’t hardwire to the ground floor ceiling.
original article on www.homebuilding.co.uk
12 Springfield Road
DESIGNED & BUILT BY
© EXTRA SPACE DEVELOPMENTS 2019 | All Rights Reserved